.
Did some anchor locker repair and used a product called VersiMold.
$8 on amazon.
It's a moldable Silicone rubber compound that you can shape anyway you want.
Then just apply some heat with a heat gun and it's now a piece of rubber.
Used it to patch my anchor locker base. Great stuff.
https://smile.amazon.com/gp/product/B00 ... UTF8&psc=1
.
VersiMold
VersiMold
You do not have the required permissions to view the files attached to this post.
2002 Cobalt 262
&
2005 Cobalt 263
496 MagHO
(sold )
Erie, PA
Currently boatless (for now)
will fly for food
(CChat moderator)
&
2005 Cobalt 263
496 MagHO
(sold )
Erie, PA
Currently boatless (for now)
will fly for food
(CChat moderator)
Re: VersiMold
Looks like good stuff!!AsLan7 wrote: ↑Thu Aug 31, 2017 6:43 pm .
Did some anchor locker repair and used a product called VersiMold.
$8 on amazon.
It's a moldable Silicone rubber compound that you can shape anyway you want.
Then just apply some heat with a heat gun and it's now a piece of rubber.
Used it to patch my anchor locker base.
.
Are you repairing scuff damage from loose anchor bounce or chain..??
Before my windlass set up on other boats I would drop a rubber impact mat in there..or sacrifice the worst life vest..
Using box anchors are hard to hold
2008 272 , 496 HO fo SHO
California Delta
Table Rock Lake
#FARCON
California Delta
Table Rock Lake
#FARCON
Re: VersiMold
cmattj wrote: ↑Thu Aug 31, 2017 6:49 pmAsLan7 wrote: ↑Thu Aug 31, 2017 6:43 pm .
Did some anchor locker repair and used a product called VersiMold.
$8 on amazon.
It's a moldable Silicone rubber compound that you can shape anyway you want.
Then just apply some heat with a heat gun and it's now a piece of rubber.
Used it to patch my anchor locker base.
.
Looks like good stuff!!
Are you repairing scuff damage from loose anchor bounce or chain..??
Before my windlass set up on other boats I would drop a rubber impact mat in there..or sacrifice the worst life vest..
Using box anchors are hard to hold
I am, Matt.
Repaired the original rubber lining with the versimold in areas where the anchor had "penetrated". Then I used another rubber mat which I siliconed on top of that (which the picture does not show). That way it is completely waterproof. I have a feeling some water was able to penetrate the old rubber mat--thus the repair.
In any event, it came out quite nice. I'll try to take a picture of the completed project next time. Just ran out of time.
2002 Cobalt 262
&
2005 Cobalt 263
496 MagHO
(sold )
Erie, PA
Currently boatless (for now)
will fly for food
(CChat moderator)
&
2005 Cobalt 263
496 MagHO
(sold )
Erie, PA
Currently boatless (for now)
will fly for food
(CChat moderator)
Re: VersiMold
Nice.. Im curious to see how it adheres to side fiberglass as I always worried about that one bounce leaving an outward splinter . I have 15 feet of chain that i just eyeball to make sure it centered on the rope and so far so good.
2008 272 , 496 HO fo SHO
California Delta
Table Rock Lake
#FARCON
California Delta
Table Rock Lake
#FARCON
Re: VersiMold
Roger that.
It adhered to the original rubber mat very well.
I also made the little "bumper" that was missing for the anchor locker to close onto. Just formed a little donut, screwed it down and heated it up. Now it's a rubber bumper.
Unfortunately, the bottom of the picture cut it off so you can't see it.
2002 Cobalt 262
&
2005 Cobalt 263
496 MagHO
(sold )
Erie, PA
Currently boatless (for now)
will fly for food
(CChat moderator)
&
2005 Cobalt 263
496 MagHO
(sold )
Erie, PA
Currently boatless (for now)
will fly for food
(CChat moderator)
Who is online
Users browsing this forum: No registered users and 3 guests