Screw holes through transom for swim deck
- thunder550
- Vice Admiral
- Posts: 2246
- Joined: Sun Oct 08, 2017 2:16 pm
- Location: Scottsdale, AZ
- Contact:
Re: Screw holes through transom for swim deck
I will contact them for sure. Need to think about what type of resolution I'm looking for, I wouldn't want them to work on it again. Will call on Monday and send these pics. Went back through some old photos and the large crack to the right has been there for awhile, not sure how I missed it
Got it back together and through-bolted. Need it to float without leaking for our upcoming Havasu trip at the end of the month. Port side was a PITA, had the bore scope through a similar hole on the other side of the stringer so I could see what I was doing, then went through this hole and got the washers started with the grabber tool and got the nuts started by taping them into the box end of the wrench. Surprised it worked. Lower photo shows exactly what I could see then whole time. Used 5200 fast cure, noon tomorrow will be 24 hours for full cure so going to dunk the boat tomorrow afternoon and see if it's still leaking.
Got it back together and through-bolted. Need it to float without leaking for our upcoming Havasu trip at the end of the month. Port side was a PITA, had the bore scope through a similar hole on the other side of the stringer so I could see what I was doing, then went through this hole and got the washers started with the grabber tool and got the nuts started by taping them into the box end of the wrench. Surprised it worked. Lower photo shows exactly what I could see then whole time. Used 5200 fast cure, noon tomorrow will be 24 hours for full cure so going to dunk the boat tomorrow afternoon and see if it's still leaking.
You do not have the required permissions to view the files attached to this post.
1995 Cobalt 252 - 502 Mag EFI - Bravo 1 - 21" Revolution 4
- Big Block Power
- Fleet Admiral
- Posts: 17904
- Joined: Sat May 07, 2016 8:05 pm
- Location: Neenah,Wi
- Contact:
Re: Screw holes through transom for swim deck
My fingers are crossed.
03Cobalt220 8.1gxi DP
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
- thunder550
- Vice Admiral
- Posts: 2246
- Joined: Sun Oct 08, 2017 2:16 pm
- Location: Scottsdale, AZ
- Contact:
Re: Screw holes through transom for swim deck
Thanks BBP, me too. Thanks for the link to that hairline crack stuff too, I'll check it out. Might try it depending on what happens with Swim Platforms.
1995 Cobalt 252 - 502 Mag EFI - Bravo 1 - 21" Revolution 4
- Big Block Power
- Fleet Admiral
- Posts: 17904
- Joined: Sat May 07, 2016 8:05 pm
- Location: Neenah,Wi
- Contact:
Re: Screw holes through transom for swim deck
If you feel up to it you can fix it your self. That crack that was there.thunder550 wrote: ↑Sat Dec 02, 2017 3:08 pm Thanks BBP, me too. Thanks for the link to that hairline crack stuff too, I'll check it out. Might try it depending on what happens with Swim Platforms.
03Cobalt220 8.1gxi DP
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
Re: Screw holes through transom for swim deck
Sorry to hear as I just caught this
You did a great Re repair and the compression of the through bolt will in itself seal it up..
As we talked about the blind holes not being blind you have no worries now . these transoms are the thickest around that I've seen.
Your ready for Havasu and Pirates cove!!
You did a great Re repair and the compression of the through bolt will in itself seal it up..
As we talked about the blind holes not being blind you have no worries now . these transoms are the thickest around that I've seen.
Your ready for Havasu and Pirates cove!!
2008 272 , 496 HO fo SHO
California Delta
Table Rock Lake
#FARCON
California Delta
Table Rock Lake
#FARCON
- Big Block Power
- Fleet Admiral
- Posts: 17904
- Joined: Sat May 07, 2016 8:05 pm
- Location: Neenah,Wi
- Contact:
Re: Screw holes through transom for swim deck
Thunder you hitting the water today?
03Cobalt220 8.1gxi DP
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
- thunder550
- Vice Admiral
- Posts: 2246
- Joined: Sun Oct 08, 2017 2:16 pm
- Location: Scottsdale, AZ
- Contact:
Re: Screw holes through transom for swim deck
Yeah I'm out here now. Makes it hard to check for leaks when you forget to put the drain plug in Remembered when I was coming back down the ramp after parking the trailer, got to go swimming. 64 degree water, brrrrrr. This is the first time I haven't worn a swimsuit too lol. Sitting here having lunch and freezing my buns off. But on the plus side..now I know my float switch isn't working
1995 Cobalt 252 - 502 Mag EFI - Bravo 1 - 21" Revolution 4
- jhnmdahl
- Vice Admiral
- Posts: 1885
- Joined: Tue Jan 06, 2015 5:11 pm
- Location: Twin Cities, MN
- Contact:
Re: Screw holes through transom for swim deck
Nice repair work, Thunder. When I think of a "pro" job, I think of things like aluminum backing plates, not installing a bolt in fiberglass with a hammer. Hope your fix lives a long and dry life!
Administrator of the www.cobaltchat.com Cobalt boats community forum
2015 210 (Volvo Penta 5.7L V8-225)
2015 210 (Volvo Penta 5.7L V8-225)
- thunder550
- Vice Admiral
- Posts: 2246
- Joined: Sun Oct 08, 2017 2:16 pm
- Location: Scottsdale, AZ
- Contact:
Re: Screw holes through transom for swim deck
Damn I didn't even think about a backing plate, now I want to redo it again
1995 Cobalt 252 - 502 Mag EFI - Bravo 1 - 21" Revolution 4
- Big Block Power
- Fleet Admiral
- Posts: 17904
- Joined: Sat May 07, 2016 8:05 pm
- Location: Neenah,Wi
- Contact:
Re: Screw holes through transom for swim deck
Never fails. someone was in a hurry to get back in the water literally.thunder550 wrote: ↑Sun Dec 03, 2017 2:34 pm Yeah I'm out here now. Makes it hard to check for leaks when you forget to put the drain plug in Remembered when I was coming back down the ramp after parking the trailer, got to go swimming. 64 degree water, brrrrrr. This is the first time I haven't worn a swimsuit too lol. Sitting here having lunch and freezing my buns off. But on the plus side..now I know my float switch isn't working
03Cobalt220 8.1gxi DP
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
Re: Screw holes through transom for swim deck
Swimming in 64 degree water ?
What are you ? A polar bear ?
What are you ? A polar bear ?
2018 r5
2003 220
2003 220
- thunder550
- Vice Admiral
- Posts: 2246
- Joined: Sun Oct 08, 2017 2:16 pm
- Location: Scottsdale, AZ
- Contact:
Re: Screw holes through transom for swim deck
Bahahaha sure felt like it, sure go ahead and make fun of the guy that lives in the oven called Phoenix. My baseline water temp is 80, so technically I was swimming in -16 degree water
I think she's good, I have a little bit of water in the bilge that the pump can't get, check it, let it sit for an hour to eat, and it's still the same. Checked the through bolts specifically and they are dry.
Also checked the float switch, when I put it back in last time I guess I laid the harness on top of it, wouldn't allow it to actually float. Moved wiring harness and it's working now.
I think she's good, I have a little bit of water in the bilge that the pump can't get, check it, let it sit for an hour to eat, and it's still the same. Checked the through bolts specifically and they are dry.
Also checked the float switch, when I put it back in last time I guess I laid the harness on top of it, wouldn't allow it to actually float. Moved wiring harness and it's working now.
1995 Cobalt 252 - 502 Mag EFI - Bravo 1 - 21" Revolution 4
- Big Block Power
- Fleet Admiral
- Posts: 17904
- Joined: Sat May 07, 2016 8:05 pm
- Location: Neenah,Wi
- Contact:
Re: Screw holes through transom for swim deck
Heck that's almost the temp of our water in the summer. Normally you don't have to worry about the float switch. It's not like it rains there.and you don't keep the boat in the water. lol
03Cobalt220 8.1gxi DP
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
"Kids in Tow2"
"Pot The Jus" Originator :-)
Neenah Wi
#ItsBu'sfault
#FARCON Marine CC Core!
- thunder550
- Vice Admiral
- Posts: 2246
- Joined: Sun Oct 08, 2017 2:16 pm
- Location: Scottsdale, AZ
- Contact:
Re: Screw holes through transom for swim deck
Thanks! After today I agree...come on Dec 28!!cmattj wrote: ↑Sat Dec 02, 2017 6:25 pm Sorry to hear as I just caught this
You did a great Re repair and the compression of the through bolt will in itself seal it up..
As we talked about the blind holes not being blind you have no worries now . these transoms are the thickest around that I've seen.
Your ready for Havasu and Pirates cove!!
Right!Big Block Power wrote: ↑Sun Dec 03, 2017 3:59 pm Heck that's almost the temp of our water in the summer. Normally you don't have to worry about the float switch. It's not like it rains there.and you don't keep the boat in the water. lol
1995 Cobalt 252 - 502 Mag EFI - Bravo 1 - 21" Revolution 4
- thunder550
- Vice Admiral
- Posts: 2246
- Joined: Sun Oct 08, 2017 2:16 pm
- Location: Scottsdale, AZ
- Contact:
Re: Screw holes through transom for swim deck
I emailed pics this morning and got a call back from them a few minutes ago. They are refunding $150 of the installation fee and told me that if the spider cracking continues to spread I can bring the boat in and they will take care of it. I think it was the owner that I talked to, he asked if I used large fender washers on the inside when through-bolting. I didn't...worth redoing for that? On the starboard side there are a couple of probably 3-4" diameter holes cut out of the top of the stringer for the bilge blower hose to attach to. Can I use a hole saw on the port side to drill similar holes? There's no way I'd be able to get a fender washer through the little tiny drain holes I don't think.
Last edited by thunder550 on Mon Dec 04, 2017 1:41 pm, edited 1 time in total.
1995 Cobalt 252 - 502 Mag EFI - Bravo 1 - 21" Revolution 4
Who is online
Users browsing this forum: No registered users and 5 guests