R6 Surf Transom Tie Downs

[Ketamarine]

Hello all, new to this forum.
I recently purchased a 2023 R6 Surf. How is everyone using transom tie downs with the surf gate and trim tabs? With current set up, I am worried there will be too much stress put on the trim tab if go down to the designed trailer hook. The surf gate blocks ability to attach to the outside of the trailer fender.

I've always used transom straps in the past, and would assume they're still necessary. If there's newer information out there I'm all ears. Just surprised with all the thought Cobalt puts into their designs, I see something as simple as this quite a flaw.

[ajcampen]

Yes, terrible set up. I can’t see any way to solve except for disconnecting the trim tab.

What does the dealer recommend?

Thanks

Andy

[Lifelongbtr]

Is there a gap between the boat and the surf gate? Seems like the only way would be to go out there to the outside of the trailer. Not ideal, I know my R7 Surf is tricky, there is a small cutout on the surf tab but unless it's on the trailer perfect it will put pressure on the surf tab.

I would look at other trailer brands too, one of the brands may of figured out a good way, or they have an option for this. Are the trim tabs in the same spot for non-surf boats?

[jhnmdahl]

Looks like there was space to move that trim tab a bit to the right - not sure why the guy bolting them on didn't see what we all seem to see...

[AsLan7]

.
So glad you found us KM...and thanks for posting that pic. You definitely do not want to put stress on that aluminum tab. We shall mull this one over. Hopefully this challenge can be overcome with some member ingenuity.

In the meantime, welcome aboard mate.

.

[BobRae99]

Looks like there was space to move that trim tab a bit to the right - not sure why the guy bolting them on didn't see what we all seem to see...

It looks like the angle that the hydraulic ram is on, it is already pretty tight at the top end. It might not install correctly if the tab was moved over (towards the centreline). I don't have a surf model but to be honest, when the dealer comes to haul my boat out for the season, I can't recall if he uses the tie downs.

[jhnmdahl]

Looks like there was space to move that trim tab a bit to the right - not sure why the guy bolting them on didn't see what we all seem to see...

It looks like the angle that the hydraulic ram is on, it is already pretty tight at the top end. It might not install correctly if the tab was moved over (towards the centreline). I don't have a surf model but to be honest, when the dealer comes to haul my boat out for the season, I can't recall if he uses the tie downs.

Good eye. It gets crowded with the surf gate there too. I wonder about moving the tie down to the right of the trim tab? Not ideal, and there may not be the same reinforcement/backing in the boat to have it there, but that seems easy enough to change in production if Cobalt were so inclined.

[bruceb58]

Have a welder put an attach point further to the outside on your trailer

[dsthomas]

Have a welder put an attach point further to the outside on your trailer

this is what you need... we have an R8 surf and did the same.

[jhnmdahl]

Have a welder put an attach point further to the outside on your trailer

Good idea. If the attachment on the trailer were on the outside of the red beam we see in the photo it might be close. I don't think I'd feel terrible about trimming back the outside edge of the trim tab just a bit if the tie-down strap still made just a little bit of contact.

[Lifelongbtr]

I looked at other trailers, they tie down towards the outside, and some have the ratchet attached to the trailer higher up, and some are putting pressure on the tabs unfortunately, see below.

But ya, some geometry and a new attachment point. If the dealer sold you this trailer with the boat, I'd be asking them.

[NautiWeasel]

By looking at the OP picture posted, I was thinking similar to what dsthomas said. See if you can add an attachment point to the outside of that trailer frame rail first. I would use a boat buckle (like what some of these other pictures have posted, and use the kind that bolt to the trailer, with a hook on the boat's transom end) that could be bolted to the outside of the trailer frame rail. From there if it were my boat, I'd probably trim that outside edge of the trim tab, as close to the transom as possible, if the tie down rubbed that part. That or put some rubber hose around your transom strap where it comes in contact with the trim tab.

Not an ideal situation, to say the least, but looks to be solvable.