Cobaltchat.com

Hello everyone. Can anyone share what the small double line 'tick' marks on the trim gauge located at approximately 4 o'clock position indicate? See image. I've looked through all my manuals with no luck. Thank you for your guidance.

.
Hey mcd. Welcome to the Cobaltchat forum. So glad you found us!

It’s difficult to see from that picture. If I had to take a gander I’d say it’s the trailerable position for the outdrive when fully raised?

Any other Cobalt pics? We enjoy them here.

Again welcome aboard mate!

.

AsLan7 wrote: Thu Aug 06, 2020 8:54 am .
Hey mcd. Welcome to the Cobaltchat forum. So glad you found us!

It’s difficult to see from that picture. If I had to take a gander I’d say it’s the trailerable position for the outdrive when fully raised?

Any other Cobalt pics? We enjoy them here.

Again welcome aboard mate!

.

I would agree. It's not red so it's all good go for it and throw a rooster

On my 2008 272, the double mark is the "level" position... trimmed to the
point where the outdrive is parallel to the boat bottom. No up or down
componenet to the thrust, just forward.

.
That makes more sense OL. Do u have a closeup pic of your gauge for reference?
.

My trim gauge has the same marks, but the marks are not referenced in the owner's manual. I was always told that the marks indicate the range of the usable trim range while underway, so you don't trim too far out while at power. This makes sense to me given the range of trim between the marks for my VP duo prop outdrive, and I suspect it's what the marks are actually intended for.

AsLan7 wrote: Fri Aug 07, 2020 1:48 am .
That makes more sense OL. Do u have a closeup pic of your gauge for reference?
.

I do not, but will snap one when next at the lake.

Sincere thanks to all for guidance. Very helpful.

Don’t need a gauge, when it looks like this you’re good.

winning!

akorcovelos wrote: Sun Aug 09, 2020 1:16 pm Don’t need a gauge, when it looks like this you’re good.


74F38FB4-20AC-4387-9CAD-FBE8BB332C18.jpeg

Was that a John Deere tractor that I saw flying out The back of that

Big Block Power wrote: Sun Aug 09, 2020 1:38 pm

akorcovelos wrote: Sun Aug 09, 2020 1:16 pm Don’t need a gauge, when it looks like this you’re good.


74F38FB4-20AC-4387-9CAD-FBE8BB332C18.jpeg

Was that a John Deere tractor that I saw flying out The back of that

John Deere snowmobile maybe. That’s why I run SS props!

akorcovelos wrote: Sun Aug 09, 2020 1:39 pm

Big Block Power wrote: Sun Aug 09, 2020 1:38 pm

akorcovelos wrote: Sun Aug 09, 2020 1:16 pm Don’t need a gauge, when it looks like this you’re good.


74F38FB4-20AC-4387-9CAD-FBE8BB332C18.jpeg

Was that a John Deere tractor that I saw flying out The back of that

John Deere snowmobile maybe. That’s why I run SS props!

Chew it up and spit it out

okielaker wrote: Fri Aug 07, 2020 6:18 pm

AsLan7 wrote: Fri Aug 07, 2020 1:48 am .
That makes more sense OL. Do u have a closeup pic of your gauge for reference?
.

I do not, but will snap one when next at the lake.

Next time, I'm at the lake:

outdrive trimmed slightly more "down" than level: outdrive trim position indicator: By the way, is there an easy way to clear the stuff on the inside
of the guage cover? Is that moisture?

.
Yes, double lines will show when the outdrive is parallel to the hull line.

.